Dlc Connector Not Working

Juni 07, 2020

I then tried with another scanner and got the same results. I checked all the fuses and they are good.

Obd2 Port Not Working How To Fix It Youtube

OBD-2 universal ISO 15765-4 CAN SAE J1850 PWM SAE J1850 VPW ISO 9141-2 ISO 14230-4 and SAE J1939 diagnostic cable.

Dlc connector not working. My diagnostic connector is not working. OBD II standards use pin 16 as power in the DLC and pins 4 and 5 as ground. OBD-2 ISO 9141-2 14230-4 KWP2000 simple serial cable.

The 740iiL models do not use the star connector. 8 Apr 28 2011. Now you can diagnose automotive wiring problem by using the diagnostic link connector of your vehicle.

Your Drivers Information Center is not working and you have no power at pin 16orange wire of your Data Link ConnectorOBDII connector. The single DME AGS and ASC control modules are. Its not just plugging in the scanner.

Attached is the diagram of the OBD connector. I tried the scanner in another vehicle and it works. Data link connector not working.

Unable to test the vehicle because OBD communications could not be established. I checked all fuses in the dash and under the hood. Ive checked the fuses an they are good I took out the OBD socket an checked the pins and they are all.

Seriously though I see this A LOT. Obd connector not working 6 Answers The odb connector is not working on my caravan. DLC communications with OBD not possible.

So you have two problems. DLC CONNECTOR NOT WORKING Customer Question I HAVE A 2004 VW BEETLE. Finally hook up the scanner to the DLC and observe the voltage reading on the DVOM.

I recently lost all forward gears on my 01 tahoe 2wd. Check your manual for the fuse location of the DLC typically it is on the cigar lighter circuit but. Some OBD-II cables schemes.

The Diagnostic Link Connector DLC Chart was developed from vehicle manufacturer responses to EPAs request for information under the Clean Air Act CAA Section 208. Not sure if it can be probed safely but pin 16 should always have battery voltage on it and pin 8 would have voltage when the ignition switch is at ON. You should see 12V between pin 16 12V and pin 4 Chassis GND.

Although we included a suggested format for the information response not all of the. Does anyone know where. I HAVE A 2004 VW BEETLE VIN3VWCD31Y84M344814 MY DLC CONNECTOR HAS NO VOLTAGE AT THE K LINE WITH KEY RADIO.

First hook up the DVOM positive lead to Pin 7 into the back of the DLC connector the ground lead attached to the chassis. A star coupler connector was used to link the individual CAN bus leads from the modules into one common connector strip. Scanner says tool not plugged up.

That fuse powes pin 16 on the DLC thats why I suggested it. Get the coins out of your cigar lighter replace the 15A cigar fuse in the underhood fuse block and stop using the cigar lighter as a coin holder lol. It is not the smartest place to put the thing and it only takes a coin toss to pop the fuse.

I failed inspection suprise to me today because my OBD will not send my info to the NJ Inspection Stations computer. Shown is your OBD2 connection above I cant recall if the diagram is the female or male connector so the pins may be reversed. The data link connector DLC is the multi-pin diagnostic connection port for automobiles trucks and motorcycles used to interface a scan tool with the control modules of a given vehicle and access on-board diagnostics and live data streams.

Vehicle testing site suggested checking the cigarette lighter fuse to see if it was either faulty or blown. The 2004 Lincoln Navigator is due for emmisions check and they could not get any power at the Data Link Connector and failed the car they said there was on power at the DLC and could not read the computer. No power at data link connector.

I hooked up an OBDII scanner to it but it would only read it was not connected to the vehicle. Neither will my buddys Android OBD reader or Advance Autos reader. Check engine light is on.

Then with the ignition switch OFF or ON there should be NO voltage on the network. Have taken my 2000 Hyundai Elantra in for state emissions testing and the results were. If this fuse blows the DLC will have no power and scan tools will not power up.

He even took an OBDII reader and plugged it in to the port in my car to show me that the port is not working the machine was not even powering up at all. Is anything else not working e. Accordingly what is a DLC fuse.

HOME SUPPORT OBD PORT LOCATOR OBD PORT LOCATOR Enter Vehicle Information Make Year Model OR Enter VIN Number 17 SUBMIT YEAR LOCATION ACCESS COMMENTS Sign up for our. It is not the smartest place to put the thing and it only takes a coin toss to pop the fuse. Any suggestio heater radio not working 3 Answers my heater.

The problem is the scanner does not power up so I checked between pins 16 V and pin 4 GND and got no voltage reading on the vehicle connector. If not located beneath the steering column look for the port in the areas indicated by numbers 4 - 9. Discussion Starter 1 Jan 11 2013.

2021 Auto wiring DLC test The quickest way to test engine wirings in 2021 has changed. OBD II standards use pin 16 as power in the DLC and pins 4 and 5. OBD-2 J1850 PWM J1850 VPW serial ELM327 cable.

When I got home I took an OBDII scanner the same one I have used several times in the past to read the codes and the machine did not connect at all to the car simply the OBDII scanner does not power up.

Obd Port Not Working Fix Youtube